FS Tool Series L01
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades for Plastic

Design:
• Tooth configuration: TC2
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For fine sizing cuts in single or double laminated panels, plexiglass and solid surface materials such as Wilsonart® Gibraltar®, SSV®; Corian®; Surell®; Avonite®; Fountainhead®, etc.
• On table saws, sliding table saws, radial arm saws and vertical panel sizing saws
• “Non-Melt” saw blades see LNM series
FS Tool Series L02
FS Tool Carbide Tipped Saw Blade: Rip Saw Blades with Chip Limiters, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged
• Saw body with chip thickness limiters

Application:
• For ripping dry soft and hardwoods
• On table saws and sliding table saws
• Ideal for hand fed operations
FS Tool Series L03
FS Tool Carbide Tipped Saw Blade: Cross Cut Saw Blades

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For cross cutting and ripping dry soft and hardwoods, plywood, masonite and raw MDF panels
• On table saws, sliding table saws and cut-off saws
FS Tool Series L03TK
FS Tool Carbide Tipped Saw Blade: Thin Kerf Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For cross cutting and ripping dry soft and hardwoods, plywood and veneered plywoods
• Not recommended to cut stock over ¾” without the use of stabilizer flanges
FS Tool Series L04
FS Tool Carbide Tipped Saw Blade: Standard Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For general cut-off and trimming of soft and hardwoods, plywood and composite panel materials, wood veneered (single sided), or (double sided) using a pre-scoring unit
• On table saws, sliding table saws and cut-off saws
FS Tool Series L05
FS Tool Carbide Tipped Saw Blade: Thin Kerf Saw Blades, TCG

Design:
• Tooth configuration: refer to chart below (grind)
• Cutting material: TC
• Expansion slots: CU plugged
• Very stable body minimizes run-out

Application:
• For fine cross cuts in veneered panels, expensive woods and sheets, thin plexiglass, masonite and plastics
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series L06
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
For fine cut-off and trimming of soft and hardwoods, plywood, wood veneered and plastic laminated panel materials
On table saws, sliding table saws and cut-off saws
FS Tool Series L07
FS Tool Carbide Tipped Saw Blade: Radial Arm Saw Blades, ATB

Design:
Tooth configuration: 4 ATB & 1 Raker
Cutting material: TC
Expansion slots: CU plugged
0° hook angle reduces the tendency of the blade grabbing the material

Application:
• For cross cutting and ripping dry soft and hardwoods
• On radial arm saws and other saws where the blade is above the work piece
FS Tool Series L09
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For fine sizing cuts in single or double sided melamine panels, MDF, OSB and HDF panels
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series L10
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For fine sizing cuts in single or double sided melamine panels, MDF, OSB and HDF panels
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series L12
FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with Chip Limiters, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged
• Saw body with chip thickness limiters

Application:
• For ripping dry soft and hardwoods
• On gang-rip saws
FS Tool Series L13
FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with 2 Rakers, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Two tungsten carbide rakers

Application:
• For ripping soft and hardwoods, dry up to 15% wood moisture
• On gang-rip saws with one or two shafts
FS Tool Series L14
FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with 2+2 Rakers, Flat Top

Design:
• Tooth configuration: Flat top
• Cutting material: TC
• Two chip clearance rakers and two wiper slots

Application:
• For ripping soft and hardwoods, wet or frozen
• On single and gang-rip saws with one or two shafts
FS Tool Series L15
FS Tool Carbide Tipped Saw Blade: Thin Rim Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged
• Thin rimmed body (on left side) allows for thin kerf at teeth and stability during cutting operation

Application:
• For fine cross cuts in veneered panels, expensive woods and sheets, thin plexiglass, masonite and plastics
• On table saws and sliding table saws
FS Tool Series L16
FS Tool Carbide Tipped Saw Blade: Thin Rim Saw Blades, TC2

Design:
• Tooth configuration: TC2
• Cutting material: TC
• Expansion slots: CU plugged
• Thin rimmed body (on left side) allows for thin kerf at teeth and stability during cutting operation

Application:
• For thin cross cuts in acrylic sheets, thin plexiglass, masonite and plastics
• On table saws and sliding table saws
FS Tool Series L18
FS Tool Carbide Tipped Saw Blade: Heavy Duty Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang-rip saws with one or two shafts
FS Tool Series L19
FS Tool Carbide Tipped Saw Blade: Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
For cross cutting and ripping soft and hardwoods, composite materials plastic laminated (single sided)
On table saws, sliding table saws and cut-off saws
FS Tool Series L1A
FS Tool Carbide Tipped Saw Blade: Saw Blades for Non-Ferrous Metals, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For splitting and mitre jointing non-ferrous extrusions, sheets and light bars
• On mitre joint, splitting, trimming, double cross-cutting and sizing machines
• Material to be cut must be clamped firmly
• Use of spray lubrication recommended
FS Tool Series L1B
FS Tool Carbide Tipped Saw Blade: Saw Blades for Non-Ferrous Metals, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For splitting and mitre jointing thin non-ferrous extrusions, thin sheets and light non-ferrous bars
• On mitre joint, splitting, trimming, double cross-cutting and sizing machines
• Material to be cut must be clamped firmly
• Use of spray lubrication recommended
FS Tool Series L1C
FS Tool Carbide Tipped Saw Blade: Standard Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang-rip saws with one or two shafts
FS Tool Series L21
FS Tool Carbide Tipped Saw Blade: Standard Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang-rip saws with one or two shafts
FS Tool Series L21TK
FS Tool Carbide Tipped Saw Blade: Thin Kerf Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang-rip saws
FS Tool Series L22
FS Tool Carbide Tipped Saw Blade: Glue Line Rip Saw Blades TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged
 
Application:
• For glue line ripping dry soft and hardwoods
• Extra smooth cut for gluing applications
• On straight line rip saws, gang-rip saws and table saws
FS Tool Series L23
FS Tool Carbide Tipped Saw Blade: Standard Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For general cut-off and trimming of plastic laminated materials (single sided), or (double sided) using a pre-scoring unit
• On table saws, sliding table saws and cut-off saws
FS Tool Series L2A
FS Tool Carbide Tipped Saw Blade: Glue Line Rip Saw Blades ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For glue line ripping dry soft and hardwoods
• Extra smooth cut for gluing applications
• On table saws
FS Tool Series L41
FS Tool Carbide Tipped Saw Blade: Hollow Face Saw Blades, TCH

Design:
Tooth configuration: TCH (face hollow-ground)
Cutting material: TC
Expansion slots: CU plugged

Application:
• For exceptionally smooth cuts (on both sides) in melamine and other laminated panels, without the need for pre-scoring
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series L42
FS Tool Carbide Tipped Saw Blade: Hollow Face Saw Blades, Hollow Ground

Design:
• Tooth configuration: inverted “V” (face hollow-ground)
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For exceptionally smooth cuts (on both sides) in melamine and other laminated panels, without the need for pre-scoring
• For mitre cuts in wrapped styrene picture frames
• On table saws, sliding table saws, vertical panel sizing saws and mitre saws
FS Tool Series L4D
FS Tool Carbide Tipped Saw Blade: Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side

Design:
• Tooth configuration: 3 beveled one side & 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately)

Application:
• For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit
• On double cut-off machines and single or double end tenoners
FS Tool Series L50
FS Tool Carbide Tipped Saw Blade: XL4000 Panel Sizing Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC XL4000
• Expansion slots: Cu plugged

Application:
• For sizing cuts in veneered particle board, hard fiberboard, raw MDF panels and high-density plywood in single sheets and stacks
• On panel sizing saws (Beam Saws)
FS Tool Series L52
FS Tool Carbide Tipped Saw Blade: XL4000 Panel Sizing Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC XL4000
• Expansion slots: Cu plugged

Application:
• For sizing cuts in plastic laminated panels and plywood in sheets and stacks
• On panel sizing saws (Beam Saws)
FS Tool Series L55
FS Tool Carbide Tipped Saw Blade: Combination Saw Blades, ATB

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC
• Four ATB teeth and one raker with deep gullet allow for deeper cuts and improved chip-flow

Application:
• For cross cutting and ripping soft and hardwoods, plywood and particleboard
• On table saws, sliding table saws and cut-off saws
FS Tool Series L6D
FS Tool Carbide Tipped Saw Blade: Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side

Design:
• Tooth configuration: 3 beveled one side & 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately)

Application:
• For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit
• On double cut-off machines and single or double end tenoners