FS Tool Saw Blades - View All
 |
FS Tool Series 527 FS Tool Carbide Tipped Saw Blade: Conic Scoring Saw Blades Design: • Tooth configuration: Conical ATB • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For pre-scoring in plastic laminated sheets • On panel sizing saws with pre-scoring units |
 |
FS Tool Series 528 FS Tool Carbide Tipped Saw Blade: Split Scoring Saw Blades, Flat Top Design • Tooth configuration: Flat Top • Cutting material: TC • Two piece unit adjustable to the kerf of the main saw blade with the use of shims Application • For pre-scoring in plastic laminated sheets • On table saws, sliding table saws and panel sizing saws with controllable pre-scoring units |
 |
FS Tool Series 529 FS Tool Carbide Tipped Saw Blade: Left Hand Scoring Saw Blades Design: • Tooth configuration: Unilaterally right • Cutting material: TC • Expansion slots: CU plugged Application: • For pre-scoring in solid wood, veneered and plastic laminated sheets • On single or double end tenoners with pre-scoring units, in combination with hogging units |
 |
FS Tool Series 530 FS Tool Carbide Tipped Saw Blade: Right Hand Scoring Saw Blades Design: • Tooth configuration: Unilaterally left • Cutting material: TC • Expansion slots: CU plugged Application: • For pre-scoring in solid wood, veneered and plastic laminated sheets • On single or double end tenoners with pre-scoring units, in combination with hogging units |
 |
FS Tool Series 531 FS Tool Carbide Tipped Saw Blade: Flat Top Scoring Saw Blades, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC • Expansion slots: CU plugged Application: • For pre-scoring in plastic laminated sheets • On single or double end tenoners with pre-scoring units, in combination with hogging units |
 |
FS Tool Series 560 FS Tool Carbide Tipped Saw Blade: Edge Banding Saw Blades Design: • Tooth configuration: see chart below (tooth shape & hook angle) • Cutting material: TC • Expansion slots: CU plugged Application: • For trimming projecting edge bandings of solid wood, wood veneer and plastics • On single and double-sided edge banding machines |
 |
FS Tool Series 1TL FS Tool Carbide Tipped Saw Blade: Segmented Hogging Units Design: • Hogger body made of light alloy equipped with 4 or 6 segments and one saw blade, all TC tipped, repalceable and resharpenable • Standrad chipping width 30 cm, wider chipping widths in multiples of 30cm can be acheived by adding mutilple elements which must be specifed when ordering Application: • For Chip free sizing of panel materails on double-ened tenoners and triming machines |
 |
FS Tool Series 1TL2 FS Tool Carbide Tipped Saw Blade: Hogging Units With Disposable Knifes Design: •High tensile strength steel body with soild carbide reversiable inserts. • Inserts have 4 cutting edges with chip breaker. • Chipping width available from 19.2mm and wider, in increments of 15mm Application: • For chip-free sizing of panel materials on double-ened tenoners and trimming machines |
 |
FS Tool Series 53DL FS Tool Carbide Tipped Saw Blade: Standard Dado Sets Design: • Standard Set adjustable from 1/4'' to 13/16'' in 1/16'' increments. Consists of two outside saw blades 1/8'' kerf, 1/4'' chipper; two 1/8'' chippers and one 1/16'' Chipper Application: • To Cut grooves and dados in soft and hardwoods, plywood and veneered panels • Used on Table saws, sliding table saws, and single or double end tenoners |
 |
FS Tool Series 53DLS FS Tool Carbide Tipped Saw Blade: Saftey Dado Sets Antikickback Design Design: • Standard Set adjustable from 1/4'' to 13/16'' in 1/16'' increments. Consists of two outside saw blades 1/8'' kerf, 1/4'' chipper; two 1/8'' chippers and one 1/16'' Chipper Application: • To Cut grooves and dados in soft and hardwoods, plywood and veneered panels • Used on Table saws, sliding table saws, and single or double end tenoners |
|
FS Tool Series 54DL FS Tool Carbide Tipped Saw Blade: Fine Dado Sets Design: • Standard Set consists of two outside saw blades 1/8'' kerf, one 1/4'' chipper; two 1/8'' chippers and one 1/16'' Chipper • Hook Angle 0º Application: • To Cut grooves and dados in plastic laminated panels • Groove widths adjustable from 1/4'' to 13/16'' maximum width in 1/16'' increments. Wider grooves can be obtained by adding spare chippers. • Used on table saws, sliding table saws, and single or double end tenoners |
 |
FS Tool Series 5G FS Tool Carbide Tipped Saw Blade: Grooving Saw Blades Design: • Tooth configuration: Flat top • Cutting material: TC Application: • For cutting grooves in soild wood, plywood, veerned and plastic laminated panels • ON table saws, sliding table saws, single or double end tenoners and CNC routers |
 |
FS Tool Series L01 FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades for Plastic Design: • Tooth configuration: TC2 • Cutting material: TC • Expansion slots: CU plugged Application: • For fine sizing cuts in single or double laminated panels, plexiglass and solid surface materials such as Wilsonart® Gibraltar®, SSV®; Corian®; Surell®; Avonite®; Fountainhead®, etc. • On table saws, sliding table saws, radial arm saws and vertical panel sizing saws • “Non-Melt” saw blades see LNM series |
 |
FS Tool Series L02 FS Tool Carbide Tipped Saw Blade: Rip Saw Blades with Chip Limiters, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC • Expansion slots: CU plugged • Saw body with chip thickness limiters Application: • For ripping dry soft and hardwoods • On table saws and sliding table saws • Ideal for hand fed operations |
 |
FS Tool Series L03 FS Tool Carbide Tipped Saw Blade: Cross Cut Saw Blades Design: • Tooth configuration: ATB • Cutting material: TC • Expansion slots: CU plugged Application: • For cross cutting and ripping dry soft and hardwoods, plywood, masonite and raw MDF panels • On table saws, sliding table saws and cut-off saws |
|
FS Tool Series L03TK FS Tool Carbide Tipped Saw Blade: Thin Kerf Cross Cut Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC • Expansion slots: CU plugged Application: • For cross cutting and ripping dry soft and hardwoods, plywood and veneered plywoods • Not recommended to cut stock over ¾” without the use of stabilizer flanges |
 |
FS Tool Series L04 FS Tool Carbide Tipped Saw Blade: Standard Cross Cut Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC • Expansion slots: CU plugged Application: • For general cut-off and trimming of soft and hardwoods, plywood and composite panel materials, wood veneered (single sided), or (double sided) using a pre-scoring unit • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series L05 FS Tool Carbide Tipped Saw Blade: Thin Kerf Saw Blades, TCG Design: • Tooth configuration: refer to chart below (grind) • Cutting material: TC • Expansion slots: CU plugged • Very stable body minimizes run-out Application: • For fine cross cuts in veneered panels, expensive woods and sheets, thin plexiglass, masonite and plastics • On table saws, sliding table saws and vertical panel sizing saws |
 |
FS Tool Series L06 FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC • Expansion slots: CU plugged Application: For fine cut-off and trimming of soft and hardwoods, plywood, wood veneered and plastic laminated panel materials On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series L07 FS Tool Carbide Tipped Saw Blade: Radial Arm Saw Blades, ATB Design: Tooth configuration: 4 ATB & 1 Raker Cutting material: TC Expansion slots: CU plugged 0° hook angle reduces the tendency of the blade grabbing the material Application: • For cross cutting and ripping dry soft and hardwoods • On radial arm saws and other saws where the blade is above the work piece |
 |
FS Tool Series L09 FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, TCG Design: • Tooth configuration: TCG • Cutting material: TC • Expansion slots: CU plugged Application: • For fine sizing cuts in single or double sided melamine panels, MDF, OSB and HDF panels • On table saws, sliding table saws and vertical panel sizing saws |
 |
FS Tool Series L10 FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, TCG Design: • Tooth configuration: TCG • Cutting material: TC • Expansion slots: CU plugged Application: • For fine sizing cuts in single or double sided melamine panels, MDF, OSB and HDF panels • On table saws, sliding table saws and vertical panel sizing saws |
 |
FS Tool Series L12 FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with Chip Limiters, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC • Expansion slots: CU plugged • Saw body with chip thickness limiters Application: • For ripping dry soft and hardwoods • On gang-rip saws |
 |
FS Tool Series L13 FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with 2 Rakers, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC • Two tungsten carbide rakers Application: • For ripping soft and hardwoods, dry up to 15% wood moisture • On gang-rip saws with one or two shafts |
 |
FS Tool Series L14 FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with 2+2 Rakers, Flat Top Design: • Tooth configuration: Flat top • Cutting material: TC • Two chip clearance rakers and two wiper slots Application: • For ripping soft and hardwoods, wet or frozen • On single and gang-rip saws with one or two shafts |
 |
FS Tool Series L15 FS Tool Carbide Tipped Saw Blade: Thin Rim Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC • Expansion slots: CU plugged • Thin rimmed body (on left side) allows for thin kerf at teeth and stability during cutting operation Application: • For fine cross cuts in veneered panels, expensive woods and sheets, thin plexiglass, masonite and plastics • On table saws and sliding table saws |
 |
FS Tool Series L16 FS Tool Carbide Tipped Saw Blade: Thin Rim Saw Blades, TC2 Design: • Tooth configuration: TC2 • Cutting material: TC • Expansion slots: CU plugged • Thin rimmed body (on left side) allows for thin kerf at teeth and stability during cutting operation Application: • For thin cross cuts in acrylic sheets, thin plexiglass, masonite and plastics • On table saws and sliding table saws |
 |
FS Tool Series L18 FS Tool Carbide Tipped Saw Blade: Heavy Duty Rip Saw Blades, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC • Expansion slots: CU plugged Application: • For ripping dry soft and hardwoods • On table saws or gang-rip saws with one or two shafts |
 |
FS Tool Series L19 FS Tool Carbide Tipped Saw Blade: Cross Cut Saw Blades, TCG Design: • Tooth configuration: TCG • Cutting material: TC • Expansion slots: CU plugged Application: For cross cutting and ripping soft and hardwoods, composite materials plastic laminated (single sided) On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series L1A FS Tool Carbide Tipped Saw Blade: Saw Blades for Non-Ferrous Metals, TCG Design: • Tooth configuration: TCG • Cutting material: TC • Expansion slots: CU plugged Application: • For splitting and mitre jointing non-ferrous extrusions, sheets and light bars • On mitre joint, splitting, trimming, double cross-cutting and sizing machines • Material to be cut must be clamped firmly • Use of spray lubrication recommended |
 |
FS Tool Series L1B FS Tool Carbide Tipped Saw Blade: Saw Blades for Non-Ferrous Metals, TCG Design: • Tooth configuration: TCG • Cutting material: TC • Expansion slots: CU plugged Application: • For splitting and mitre jointing thin non-ferrous extrusions, thin sheets and light non-ferrous bars • On mitre joint, splitting, trimming, double cross-cutting and sizing machines • Material to be cut must be clamped firmly • Use of spray lubrication recommended |
 |
FS Tool Series L1C FS Tool Carbide Tipped Saw Blade: Standard Rip Saw Blades, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC • Expansion slots: CU plugged Application: • For ripping dry soft and hardwoods • On table saws or gang-rip saws with one or two shafts |
 |
FS Tool Series L21 FS Tool Carbide Tipped Saw Blade: Standard Rip Saw Blades, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC • Expansion slots: CU plugged Application: • For ripping dry soft and hardwoods • On table saws or gang-rip saws with one or two shafts |
 |
FS Tool Series L21TK FS Tool Carbide Tipped Saw Blade: Thin Kerf Rip Saw Blades, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC • Expansion slots: CU plugged Application: • For ripping dry soft and hardwoods • On table saws or gang-rip saws |
 |
FS Tool Series L22 FS Tool Carbide Tipped Saw Blade: Glue Line Rip Saw Blades TCG Design: • Tooth configuration: TCG • Cutting material: TC • Expansion slots: CU plugged Application: • For glue line ripping dry soft and hardwoods • Extra smooth cut for gluing applications • On straight line rip saws, gang-rip saws and table saws |
 |
FS Tool Series L23 FS Tool Carbide Tipped Saw Blade: Standard Cross Cut Saw Blades, TCG Design: • Tooth configuration: TCG • Cutting material: TC • Expansion slots: CU plugged Application: • For general cut-off and trimming of plastic laminated materials (single sided), or (double sided) using a pre-scoring unit • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series L2A FS Tool Carbide Tipped Saw Blade: Glue Line Rip Saw Blades ATB Design: • Tooth configuration: ATB • Cutting material: TC • Expansion slots: CU plugged Application: • For glue line ripping dry soft and hardwoods • Extra smooth cut for gluing applications • On table saws |
 |
FS Tool Series L41 FS Tool Carbide Tipped Saw Blade: Hollow Face Saw Blades, TCH Design: Tooth configuration: TCH (face hollow-ground) Cutting material: TC Expansion slots: CU plugged Application: • For exceptionally smooth cuts (on both sides) in melamine and other laminated panels, without the need for pre-scoring • On table saws, sliding table saws and vertical panel sizing saws |
 |
FS Tool Series L42 FS Tool Carbide Tipped Saw Blade: Hollow Face Saw Blades, Hollow Ground Design: • Tooth configuration: inverted “V” (face hollow-ground) • Cutting material: TC • Expansion slots: CU plugged Application: • For exceptionally smooth cuts (on both sides) in melamine and other laminated panels, without the need for pre-scoring • For mitre cuts in wrapped styrene picture frames • On table saws, sliding table saws, vertical panel sizing saws and mitre saws |
 |
FS Tool Series L4D FS Tool Carbide Tipped Saw Blade: Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side Design: • Tooth configuration: 3 beveled one side & 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately) Application: • For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit • On double cut-off machines and single or double end tenoners |
 |
FS Tool Series L50 FS Tool Carbide Tipped Saw Blade: XL4000 Panel Sizing Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC XL4000 • Expansion slots: Cu plugged Application: • For sizing cuts in veneered particle board, hard fiberboard, raw MDF panels and high-density plywood in single sheets and stacks • On panel sizing saws (Beam Saws) |
 |
FS Tool Series L52 FS Tool Carbide Tipped Saw Blade: XL4000 Panel Sizing Saw Blades, TCG Design: • Tooth configuration: TCG • Cutting material: TC XL4000 • Expansion slots: Cu plugged Application: • For sizing cuts in plastic laminated panels and plywood in sheets and stacks • On panel sizing saws (Beam Saws) |
 |
FS Tool Series L55 FS Tool Carbide Tipped Saw Blade: Combination Saw Blades, ATB Design: • Tooth configuration: 4 ATB & 1 Raker • Cutting material: TC • Four ATB teeth and one raker with deep gullet allow for deeper cuts and improved chip-flow Application: • For cross cutting and ripping soft and hardwoods, plywood and particleboard • On table saws, sliding table saws and cut-off saws |
|
FS Tool Series L6D FS Tool Carbide Tipped Saw Blade: Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side Design: • Tooth configuration: 3 beveled one side & 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately) Application: • For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit • On double cut-off machines and single or double end tenoners |
 |
FS Tool Series LHCF FS Tool Carbide Tipped Saw Blade: Chip-Free Melamine Trim Blades Design: • Tooth configuration: High ATB (30 degrees) • Cutting material: TC • Expansion slots: Laser, Self plug Application: • For chip free sizing cuts (on both sides) in melamine and wood veneered panels, without the need for pre-scoring • For fine cross-cuts in solid woods • On table saws, sliding table saws, vertical panel sizing saws and cut-off saws |
|
FS Tool Series LHCP FS Tool Carbide Tipped Saw Blade: Combination/Planer Saw Blades Design: • Tooth configuration: 4 ATB & 1 Raker • Cutting material: TC • Four ATB teeth and one raker with deep gullet allow for deeper cuts and improved chip flow Application: • For cross cutting and ripping dry soft and hardwoods, plywood and particleboard • On portable machines and Table saws |
 |
FS Tool Series LHCS FS Tool Carbide Tipped Saw Blade: Saw Blades For Cordless Machines Design: • Cutting material: TC • Expansion slots: laser, self plug Application: • For cross cutting solid wood, veneered and plastic laminated sheets • On portable machines |
|
FS Tool Series LHFC FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades Design: • Cutting material: TC • Expansion slots: laser, self plug Application: • For fine cut-off and trimming of solid woods, plywood, wood veneered and plastic laminated panel materials • On portable machines and table saws |
 |
FS Tool Series LHGA FS Tool Carbide Tipped Saw Blade: General Application Saw Blades Design: • Cutting material: TC • Expansion slots: laser, self plug Application: • For ripping and general cross cutting of dry solid woods • On portable machines and table saws |
 |
FS Tool Series LHMJ FS Tool Carbide Tipped Saw Blade: Mitre Joint Saw Blades Design: • Tooth configuration: 4 ATB & 1 Raker • Cutting material: TC • Expansion slots: laser, self plug Application: • For mitre joint cuts in soft and hardwood picture frames and furniture mouldings • On cut-off mitre machines, compound mitre machines, radial arm saws, and table saws |
 |
FS Tool Series LHRS FS Tool Carbide Tipped Saw Blade: Demolition-Firemans Saw Blades Design: • Tooth configuration: TCGN • Cutting material: TC • Modified grind and 15 degrees negative hook reduces the possibility of tooth damage Application: • For rough cutting applications • On gasoline powered machines |
|
FS Tool Series LHSC FS Tool Carbide Tipped Saw Blade: Mitre Joint Saw Blades, ATB Design: • Tooth configuration: 4 ATB & 1 Raker • Cutting material: TC • Expansion slots: CU plugged Application: • For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as P.V.C. substrates • For aluminum cuts see L1A, L1B, L1C series page E36, E37 • On single or double cut-off mitre machines and radial arm saws |
|
FS Tool Series LM4 FS Tool Carbide Tipped Saw Blade: Mitre Joint Saw Blades, ATB Design: • Tooth configuration: 4 ATB & 1 Raker • Cutting material: TC • Expansion slots: CU plugged Application: • For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as P.V.C. substrates • For aluminum cuts see L1A, L1B, L1C series page E36, E37 • On single or double cut-off mitre machines and radial arm saws |
|
FS Tool Series LM6 FS Tool Carbide Tipped Saw Blade: Mitre Joint Saw Blades, ATB Design: • Tooth configuration: 4 ATB & 1 Raker • Cutting material: TC • Expansion slots: CU plugged Application: • For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as P.V.C. substrates • For aluminum cuts see L1A, L1B, L1C series page E36, E37 • On single or double cut-off mitre machines and radial arm saws |
 |
FS Tool Series LM6-30° FS Tool Carbide Tipped Saw Blade: Chip-Free Melamine Trim Blades, High ATB (30°) Design: • Tooth configuration: High ATB (30°) • Cutting material: TC • Expansion slots: CU plugged Application: • For chip-free sizing cuts (on both sides) in melamine and wood veneered panels, without the need for pre-scoring • For fine cross cuts in solid woods • On table saws, sliding table saws, vertical panel sizing saws and cut-off saws |
 |
FS Tool Series LNM FS Tool Carbide Tipped Saw Blade: Non-Melt Saw Blades, TC2 Design: • Tooth configuration: TC2 • Tooth geometry specifically designed to minimize “melting” of material • Cutting material: TC • Expansion slots: CU plugged Application: • For “non-melt” fine cuts in acrylic sheets, selrins, ABS (cycolac), Styrenes and PVC • On table saws, sliding table saws and vertical panel sizing saws |
 |
FS Tool Series S03 FS Tool Carbide Tipped Saw Blade: XL4000 Cross Cut Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For cross cutting and ripping dry soft and hardwoods, plywood, masonite and raw MDF panels • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series S04 FS Tool Carbide Tipped Saw Blade: XL4000 Fine Cross Cut Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For fine cut-off and trimming of soft and hardwoods, plywood, wood veneered and plastic laminated panel materials • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series S06 FS Tool Carbide Tipped Saw Blade: XL4000 Fine Cross Cut Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For fine cut-off and trimming of soft and hardwoods, plywood, wood veneered and plastic laminated panel materials • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series S07 FS Tool Carbide Tipped Saw Blade: XL4000 Radial Arm Saw Blades, ATB Design: • Tooth configuration: 4 ATB & 1 Raker • Cutting material: TC XL4000 • Expansion slots: CU plugged • 0° hook angle reduces the tendency of the blade grabbing the material Application: • For cross cutting and ripping dry soft and hardwoods • On radial arm saws and other saws where the blade is above the work piece |
|
FS Tool Series S09 FS Tool Carbide Tipped Saw Blade: XL4000 Cross Cut Saw Blades, ATB Design: • Tooth configuration: ATB • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For cross cutting and ripping dry soft and hardwoods, plywood, masonite and raw MDF panels • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series S10 FS Tool Carbide Tipped Saw Blade: XL4000 Fine Cross Cut Saw Blades, TCG Design: • Tooth configuration:TCG • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For fine sizing cuts in single or double sided melamine panels, MDF, OSB and HDF panels • On table saws, sliding table saw and vertical panel sizing saws |
 |
FS Tool Series S19 FS Tool Carbide Tipped Saw Blade:XL4000 Cross Cut Saw Blades, TCG Design: • Tooth configuration: TCG • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For cross cutting and ripping dry soft and hardwoods • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series S21 FS Tool Carbide Tipped Saw Blade: XL4000 Heavy Duty Rip Saw Blades, Flat Top Design: • Tooth configuration: Flat Top • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For ripping dry soft and hardwoods • On table saws or gang rip saws with one or two shafts |
 |
FS Tool Series S22 FS Tool Carbide Tipped Saw Blade: XL4000 Glue Line Rip Saw Blades, TCG Design: • Tooth configuration: TCG • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For glue line ripping dry soft and hardwoods • Extra smooth cut for gluing applications • On straight line rip saws, gang rip saws and table saw |
 |
FS Tool Series S23 FS Tool Carbide Tipped Saw Blade: XL4000 Standard Cross Cut Saw Blades, TCG Design: • Tooth configuration: TCG • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For general cut-off and trimming of plastic laminated materials (single sided), or (double sided) using a pre-scoring unit • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series S4D FS Tool Carbide Tipped Saw Blade: XL4000 Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side Design: • Tooth configuration: 3 beveled one side and 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately) Application: • For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit • On double cut-off machines and single or double end tenoners |
 |
FS Tool Series S55 FS Tool Carbide Tipped Saw Blade: XL4000 Combination/Planer Saw Blades, ATB Design: • Tooth configuration: 4 ATB & Raker • Cutting material: TC XL4000 • Four ATB teeth and one raker with deep gullet allow for deeper cuts and improved chip-flow Application: • For cross cutting and ripping dry soft and hardwoods, plywood and particleboard • On table saws, sliding table saws and cut-off saws |
 |
FS Tool Series S6D FS Tool Carbide Tipped Saw Blade: XL4000 Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side Design: • Tooth configuration: 3 beveled one side and 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately) Application: • For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit • On double cut-off machines and single or double end tenoners |
 |
FS Tool Series SM6 FS Tool Carbide Tipped Saw Blade: XL4000 Mitre Joint Saw Blades, ATB Design: • Tooth configuration: 4 ATB & 1 Raker • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as PVC substrates • For aluminum cuts see L1A, L1B, L1C, series • On single side or double cut-off mitre machines and radial arm saws |
 |
FS Tool Series SM6-30° FS Tool Carbide Tipped Saw Blade: XL4000 Chip-Free Melamine Trim Blades, High ATB (30°) Design: • Tooth configuration: High ATB (30°) • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For chip-free sizing cuts (on both sides) in melamine and wood veneered panels, without the need for pre-scoring • For fine cross cuts in solid woods • On table saws, sliding table saws, vertical panel sizing saws and cut-off saws |
 |
FS Tool Series SS1 FS Tool Carbide Tipped Saw Blade: XL4000 Solid Surface Saw Blades, TC2 Design: • Tooth configuration: TC2 • Cutting material: TC XL4000 • Expansion slots: CU plugged Application: • For fine sizing cuts in single or double laminated panels, plexiglass and solid surface materials such as Wilsonart® Gibraltar®, SSV®; Corian®; Surell®; Avonite®; Fountainhead®, etc. • On table saws, sliding table saws, radial arm saws and vertical panel sizing saws |